Is this a printable part? If so would anyone mind sharing the link to the file?
Thanks.
Search found 19 matches
- Sun Feb 28, 2016 8:38 pm
- Forum: Tech Support
- Topic: Filament drive replacement print
- Replies: 7
- Views: 9268
- Wed Nov 05, 2014 10:16 pm
- Forum: M2 Dual Extruder
- Topic: v4 Status
- Replies: 132
- Views: 150340
Re: v4 Status
woot!!!
- Wed Nov 05, 2014 10:12 pm
- Forum: How-to/Guides/Tips
- Topic: acetone vapor smoothing (again)
- Replies: 2
- Views: 6368
Re: acetone vapor smoothing (again)
brilliant!
- Wed Nov 05, 2014 10:11 pm
- Forum: General Discussion
- Topic: type of oil to lubricate rails in m2
- Replies: 13
- Views: 18343
Re: type of oil to lubricate rails in m2
Local Music shops or amazon, Trombone Slide Cream. its the way to go.
- Mon Nov 03, 2014 8:42 pm
- Forum: Tech Support
- Topic: M2 RAMBo And MW SE-450-24 PSU Wiring diagram or schematics
- Replies: 10
- Views: 16901
Re: M2 RAMBo And MW SE-450-24 PSU Wiring diagram or schemati
I apologize, I failed to ever post conclusive information. probably two or three days from my last post on this topic, I had successfully identified the proper terminations and their purposes.
It's been too long to really say more than, it was just a swapped conductor.
It's been too long to really say more than, it was just a swapped conductor.
- Fri Oct 10, 2014 6:22 pm
- Forum: General Discussion
- Topic: type of oil to lubricate rails in m2
- Replies: 13
- Views: 18343
Re: type of oil to lubricate rails in m2
I used to played trombone for 3 years, I would Imagine the Slide Oil or Slide Cream Would be hard to beat. Caution Trombone Tuning Slide Grease Is Not the same thing im referring to. It is for a seperate part of the instrument, and is nothing more than Petroleum jelly. Also having owned A nice fusbo...
- Mon Sep 29, 2014 6:15 pm
- Forum: General Discussion
- Topic: Prints with rounded/arched bridging
- Replies: 5
- Views: 7922
Re: Prints with rounded/arched bridging
Thank you all for your replies, We will try to get a picture up asap as to better illustrate our complications. Also we are printing PLA 1.75mm with a .35mm extruder nozzle and set at .3mm in Simplify 3D. Also Consider it more to be sagging/separating exterior layers of this particular print. We are...
- Thu Sep 25, 2014 9:26 pm
- Forum: General Discussion
- Topic: Prints with rounded/arched bridging
- Replies: 5
- Views: 7922
Prints with rounded/arched bridging
Hello, We are experiencing difficulties printing objects with rounded corners, typically the layers sagging, sometimes a little sometime a lot. We print with simplify 3d and love it but this issue has been recurring throughout the entire duration we have been printing. Has anyone had issues with arc...
- Thu Sep 25, 2014 9:17 pm
- Forum: How-to/Guides/Tips
- Topic: Stop your geared stepped motors from grinding!
- Replies: 6
- Views: 9706
Stop your geared stepped motors from grinding!
Check the endstops!! The M2 I am familiar with had been grinding gears from improper endstop positioning. They can become contorted and bend, if this happens carefully (perhaps with needle nose pliers) bend the endstops back into a positon as where, once the bed plate hit them, you should hear/feel ...
- Sun Aug 10, 2014 1:35 am
- Forum: Tech Support
- Topic: Y Axis Motor issue
- Replies: 4
- Views: 7272
Re: Y Axis Motor issue
Gents,
Thank You for the responses.
It actually prints well. It has recently begun to over extend the Y Axis and make the grinding noise just before it starts.
I will look at s3d, but it did not do this previously.
Thank You
Thank You for the responses.
It actually prints well. It has recently begun to over extend the Y Axis and make the grinding noise just before it starts.
I will look at s3d, but it did not do this previously.
Thank You