Search found 2888 matches
- Tue Sep 18, 2018 3:21 pm
- Forum: Modifications
- Topic: Mic 6 tooling plate
- Replies: 212
- Views: 353241
Re: Mic 6 tooling plate
i dont. i quit making those some years ago. insta took over for awhile. not sure if he still does that. for the shimming, it doesnt need to be dead nuts on both plates. just split the difference. if you can get them within .05, that should be good.
- Mon Sep 17, 2018 9:25 pm
- Forum: Modifications
- Topic: Mic 6 tooling plate
- Replies: 212
- Views: 353241
Re: Mic 6 tooling plate
i havent been on the forum other than a couple times the past year myself. i still use mic6 with hairspray on both my printers. wouldnt use anything else. it works for pretty much everything. as for the flatness, its probably not your build platform. you need to shim the x-rail to match the plate. n...
- Tue Sep 11, 2018 4:45 am
- Forum: General Discussion
- Topic: Introducing Ultra One
- Replies: 21
- Views: 65259
Re: Introducing Ultra One
haha yeah its been a while. i have been so busy with work the past year i havent had time for much else....unfortunately
- Mon Sep 10, 2018 5:05 pm
- Forum: General Discussion
- Topic: Introducing Ultra One
- Replies: 21
- Views: 65259
Re: Introducing Ultra One
man its been a long time since i have been on the forum and posted but this deserves it! very nice rick. i am happy to see something fresh from makergear with a different core design from the m2. i would honestly order one of these today if my m2's didnt do such a good job. 5 years later and they ar...
- Fri Nov 17, 2017 5:24 am
- Forum: General Discussion
- Topic: How Do I Get Rid of fine spider threads between parts?
- Replies: 5
- Views: 16216
Re: How Do I Get Rid of fine spider threads between parts?
lower your print temp to reduce the fuzz but not so low you have adhesion issues. lower your temp 5 deg at a time until it goes away
- Fri Nov 17, 2017 5:22 am
- Forum: M2 Dual Extruder
- Topic: Single Outside Layer
- Replies: 3
- Views: 25706
Re: Single Outside Layer
print the switch in black then paint it white and laser through the paint. i have never used a laser so im just guessing if that would work. if switches are printed in abs and you paint with a solvent base paint then it will bond like crazy without any prep.
- Wed Nov 08, 2017 2:18 am
- Forum: Filament
- Topic: Aging of PETG Filament?
- Replies: 8
- Views: 22072
Re: Aging of PETG Filament?
thats prob not the issue. you could have the filament tension set too high which will cause you to squish the filament out of round and make it tight going through the filament path and extruder. can also be a partially clogged nozzle or the hot end is getting tight from buildup. this usually happen...
- Wed Nov 08, 2017 2:09 am
- Forum: Tech Support
- Topic: Steps in Diagonal Lines
- Replies: 6
- Views: 14128
Re: Steps in Diagonal Lines
if your speaking of that wavy pattern in the filament on the first layer then insta is right. that is from printing too close to the bed. the filament is squishing out causing that. it will take a few layers to recover from that and get clean straight extrusions
- Mon Oct 23, 2017 2:12 am
- Forum: Filament
- Topic: PLA Plus Other Than eSun?
- Replies: 10
- Views: 32242
Re: PLA Plus Other Than eSun?
i know and i have used it. i have used esun almost exclusively for 3 years. its not a specialty material. its pla just a slightly better grade/formulation. its not as hard and brittle. keep in mind when a company claims their material is stronger, that is a huge generalization. every material is str...
- Mon Oct 23, 2017 1:46 am
- Forum: Filament
- Topic: PLA Plus Other Than eSun?
- Replies: 10
- Views: 32242
Re: PLA Plus Other Than eSun?
just look for any pla. pla+ from esun isnt the same as pla+ from another comapny. its just a name esun gave their premium pla line. its not a specific type of pla.