Temperature Issues (First time user)
Posted: Mon Oct 27, 2014 7:37 pm
(sorry meant to post in the help section)
Recently got the MakerGear M2. Using Simplify 3D.
Its the RAMBo type, and i installed the RAMBo drivers.
When I go to the machine control panel i have some issues.
-Connects fine.
-Jog controls work fine.
-But if i try to activate the heating bed or extruder the program locks up. The G-Code is sent but nothing happens. After requesting the temperature a few times the printer restarts itself without heating up. Below is a copy of the communication log after I sent the heating code.
SENT: M105
RECEIVED: ok T:21.2 /0.0 B:21.6 /0.0 @:0
SENT: M105
RECEIVED: ok T:21.2 /0.0 B:21.6 /0.0 @:0
SENT: M140 S70
RECEIVED: ok
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
RECEIVED:
RECEIVED: echo:Marlin: 1.0.0 RC2 for MakerGear M2, 24V with 24V/40W heater
Marlin: 1.0.0 RC2 for MakerGear M2, 24V with 24V/40W heater
RECEIVED: echo: Last Updated: 2012-05-30 | Author: johnny
Last Updated: 2012-05-30 | Author: johnny
RECEIVED: echo: Free Memory: 4775 PlannerBufferBytes: 1232
Free Memory: 4775 PlannerBufferBytes: 1232
RECEIVED: echo:Using Default settings:
Using Default settings:
RECEIVED: echo:Steps per unit:
Steps per unit:
RECEIVED: echo: M92 X88.88 Y88.88 Z400.00 E471.50
M92 X88.88 Y88.88 Z400.00 E471.50
RECEIVED: echo:Maximum feedrates (mm/s):
Maximum feedrates (mm/s):
RECEIVED: echo: M203 X500.00 Y500.00 Z250.00 E200000.00
M203 X500.00 Y500.00 Z250.00 E200000.00
RECEIVED: echo:Maximum Acceleration (mm/s2):
Maximum Acceleration (mm/s2):
RECEIVED: echo: M201 X9000 Y9000 Z30 E10000
M201 X9000 Y9000 Z30 E10000
RECEIVED: echo:Acceleration: S=acceleration, T=retract acceleration
Acceleration: S=acceleration, T=retract acceleration
RECEIVED: echo: M204 S3000.00 T3000.00
M204 S3000.00 T3000.00
RECEIVED: echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)
Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)
RECEIVED: echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
RECEIVED: echo:PID settings:
PID settings:
RECEIVED: echo: M301 P25.89 I1.94 D86.53
M301 P25.89 I1.94 D86.53
RECEIVED: echo:SD card ok
SD card ok
Any thoughts on why this might be occuring?
Recently got the MakerGear M2. Using Simplify 3D.
Its the RAMBo type, and i installed the RAMBo drivers.
When I go to the machine control panel i have some issues.
-Connects fine.
-Jog controls work fine.
-But if i try to activate the heating bed or extruder the program locks up. The G-Code is sent but nothing happens. After requesting the temperature a few times the printer restarts itself without heating up. Below is a copy of the communication log after I sent the heating code.
SENT: M105
RECEIVED: ok T:21.2 /0.0 B:21.6 /0.0 @:0
SENT: M105
RECEIVED: ok T:21.2 /0.0 B:21.6 /0.0 @:0
SENT: M140 S70
RECEIVED: ok
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
SENT: M105
RECEIVED:
RECEIVED: echo:Marlin: 1.0.0 RC2 for MakerGear M2, 24V with 24V/40W heater
Marlin: 1.0.0 RC2 for MakerGear M2, 24V with 24V/40W heater
RECEIVED: echo: Last Updated: 2012-05-30 | Author: johnny
Last Updated: 2012-05-30 | Author: johnny
RECEIVED: echo: Free Memory: 4775 PlannerBufferBytes: 1232
Free Memory: 4775 PlannerBufferBytes: 1232
RECEIVED: echo:Using Default settings:
Using Default settings:
RECEIVED: echo:Steps per unit:
Steps per unit:
RECEIVED: echo: M92 X88.88 Y88.88 Z400.00 E471.50
M92 X88.88 Y88.88 Z400.00 E471.50
RECEIVED: echo:Maximum feedrates (mm/s):
Maximum feedrates (mm/s):
RECEIVED: echo: M203 X500.00 Y500.00 Z250.00 E200000.00
M203 X500.00 Y500.00 Z250.00 E200000.00
RECEIVED: echo:Maximum Acceleration (mm/s2):
Maximum Acceleration (mm/s2):
RECEIVED: echo: M201 X9000 Y9000 Z30 E10000
M201 X9000 Y9000 Z30 E10000
RECEIVED: echo:Acceleration: S=acceleration, T=retract acceleration
Acceleration: S=acceleration, T=retract acceleration
RECEIVED: echo: M204 S3000.00 T3000.00
M204 S3000.00 T3000.00
RECEIVED: echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)
Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum xY jerk (mm/s), Z=maximum Z jerk (mm/s)
RECEIVED: echo: M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
M205 S0.00 T0.00 B20000 X20.00 Z0.40 E5.00
RECEIVED: echo:PID settings:
PID settings:
RECEIVED: echo: M301 P25.89 I1.94 D86.53
M301 P25.89 I1.94 D86.53
RECEIVED: echo:SD card ok
SD card ok
Any thoughts on why this might be occuring?